• The excellent people at AirWorks are simply the best! Their service is delivered with a high level of HVAC knowledge as well as integrity and honesty . I appreciate working with everyone at AirWorks.Pamela M.
  • Thanks Airworks for working long hours and staying late to finish our project ! Thanks for having a polite efficient and friendly staff. We appreciate your outstanding service French family !Debby Hellickson F.
  • Bill was awesome! First he talked us through getting our heater started. Then, when it died again the next day, a Sunday, he came out and fixed it! Very honest and upfront about charges which we greatly appreciate.Elise Van V.
  • Thermostat replacement Very well, very thorough and professional.Airworks Client
Blog
Q&A Comfort Advise

Fun with Pumps and Circulators

Q: Your technician replaced one of our pumps on our boiler system. We have several others left that may fail, should we be replacing them all?

A:  To start with, and to clarify some boiler vernacular, we replaced a “circulator”, not to be confused with a “pump”, more on that below during the amazing conclusion of the article. This circulator replaced may have been one of many, but often its service life depends on the purpose and how it was piped. Most residential boiler systems will have at least one circulator and depending on the size of the system, perhaps an entire wall of them (hint: more is not always better, BUT size always matters). One properly sized circulator can provide adequate flow to an average sized home with baseboard heaters or big ol’ fat radiators. This is due to their relatively low restriction in the elements and distribution. Adding all the modern accoutrements to a system such as multiple zones, radiant, indirect fired water heating, snow melt, etc, is where flow challenges are created.

       There are any number of heating and cooling systems AirWorks is required to design, repair, and maintain. With “hydronics” (more boiler vernacular), this is the application of heat transfer using water as the medium. Just like an artist’s medium may be oils, watercolors, or tin foil (?), ours, in this case is water. Creating (or often redesigning) a system that will providing consistent water flow and thus heat transfer, and thus warm feet is what it’s all about. Often boiler rooms, big and small (usually too small) can be an overwhelming mazes of pipes, plumbing, and control wiring. Compared to a furnace where it’s normally return air ducting into a rectangular box, and hot air out the top, wa-la! Boiler rooms rarely release their secrets quite that easy. The comings and goings of all those pipes have consistent properties of BTU content and flow rates. Our job is to decipher that with a few well placed temperature reading instruments and voltage meters. If we are lucky, the solution is a worn out circulator (if we could ever be so lucky).

         Back to the question at hand. The circulator that was replaced was installed in the “primary loop”, which is the main driver of water moving through the boiler. This component will be running anytime the boiler system is heating, no matter what task is occurring. The odds of a shorter service life are ensured however ten years or better should be expected. Any number of situations could negatively affect how long one may last. Water quality is a biggie and this usually goes south from improperly mixing cast iron (ferrous metals) with copper and brass (non-ferrous) metals. This di-electric corrosion of the cast iron will slowly create leaks and leave particulate floating around just waiting to scour bearings and clog stuff up. Air in the hydronic system as well as low system pressure can cause pumps to cavitate and suffer a quick (and usually) noisy ending. AirWorks maintains boilers to prevent just this sort of thing. If you have a have a boiler system, you may have found they are easy to ignore with no filters to change but left unattended, especially for years, be afraid, be very afraid.

       As the drums roll, the crowd leans forward awkwardly awaiting the differences in the definition between a pump and a circulator. As it was explained to me, a circulator is like motor driving a Ferris wheel. Since a boiler system is a “closed system” it just moves water up to the heat emitters and then back down to the boiler, and again, and again. A pump is designed to overcome atmospheric pressure and move water, say from a well to your water heater, to you shower head, and AAAAA, pure bliss. So now you know, and let us know if AirWorks can help maintain your boiler system. We are scheduling now for the spring season, call (406) 630-4170

Bill Yarus

Share
Published by
Bill Yarus

Recent Posts

Five Benefits of Variable-Speed HVAC Systems

An air conditioner or heat pump compressor made with variable-speed technology is one that allows…

6 years ago

Thermal Tracking: What It Is and How to Prevent It

Thermal tracking is also known as thermal bridging or ghosting. AirWorks, your heater and air…

6 years ago

Do it Yourself Thermostat Installations

Q: I changed my own thermostat and now my bill are through the roof, what’s…

7 years ago

Is Your Heat Pump Leaking Refrigerant Again?

Q: Another refrigerant leak on my heat pump, is there a better way?    A:…

7 years ago

How to Maintain Healthy Humidity Levels in Your Home

Household humidity plays an important role in maintaining your home’s indoor air quality. You want…

7 years ago

What to Do When Your Furnace Fans Are Not Switching Off

Now that the warmer days of spring are just around the corner, this is the…

7 years ago